Common Vacuum Cleaner Problems and Their Possible Fix!

Vacuum cleaners are responsible for keeping your floors clean & your home free of dust. Because vacuum cleaners are used so frequently in almost all houses, there is a good risk that yours will break down sooner or later. It’s critical to understand what has happened and how to correct it if this occurs.

Vacuum cleaners are the first line of defense against flying dog fur and tracked-in filth in the home, and they are available to everyone. When your go-to remedy against filth is no longer effective, you might be inclined to give up and call it quits.

cleaning a vacuum

However, not every issue necessitates the replacement of the vehicle with a newer model. Among the most frequent vacuum, cleaner the difficulties are discussed in this section along with suggestions for how to save your vacuum cleaner.

Loss of Suction

When you’ve spent moments vacuuming a single location with no obvious improvements, there’s nothing more aggravating than that.

Your vacuum may have lost the suction because of a clog somewhere within the system, which is easy to diagnose. If your vacuum is having a bag, ensure sure it isn’t full before using it. If your bag isn’t empty, but the section that contains it is suffocating under the weight of dust and filth, it’s likely that you have a hole in it and it’s time to change it.

Vacuum Cleaner Suction

Examine its seal on the debris bin if you’re using a bag less vacuum. If they are broken or appear to be damaged & dried out, it could be necessary to replace the shingles.

You should clean your vacuum cleaner regularly, regardless of whether it is bagless or not. Vacuum cleaners are typically equipped with numerous filters that become clogged. A blockage in a filter indicates that there is not enough air passing through the device to provide the necessary suction.

Alternatively, the problem could be with your machine’s hoses. Check for obstructions and damage to the intake valve, such as cracks and holes, as well as any debris accumulation. Perhaps it is time to get these components repaired or replaced.

When the Vacuum cleaner is not turning on

Is it connected to anything? Of course, it’s connected to the power source. However, a plugin your home just ceases to function properly. Even though all of your plugs are operational, they may require the activation of a light switch to give power. That’s frustrating, but we’ve all been in that situation.

Check the continuity of your on-off button with the help of an ohmmeter, a multi-meter, or another continuity checking instrument. They are inexpensive. In any case, you should buy in one to have about the house as a backup.

Here’s a nice explanation on how to make use of an ohmmeter.

If it’s getting electricity, but its motor doesn’t operate, the fault generally rests with the engine itself. If the engine can acquire power, ensure the shaft can revolve freely without hindrance. Here’s a short review of how the vacuum works and what major sections of the engine look like.

If the engine is gaining power, turning easily, and yet not functioning, you likely need to visit a specialist or find a new motor.

When it is not spinning

The vacuum belt is once again to blame for the lack of spinning. If any of these belts are found to be damaged or excessively stretched, the cleaning brush will be unable to spin properly. Check the condition of the drive belt as well as its cogged belt to check that they are in proper operating order. If either one of them is damaged, you will have to get them repaired or replace them.

In addition, it’s conceivable that the brushing roll has been jammed. Removing the brushing roll from the cleaner and thoroughly cleaning it before reinstalling it is recommended. It is necessary to have the brushing roll assembly changed if it is broken or cracked.

Facing difficulty in pushing

A vacuum cleaner that is hard to push may simply be influenced by a buildup of dust on the bottom plate of the vacuum cleaner itself. Any quality furniture polish can be used to clean the base plate, which will allow for smooth motion over carpets and rugs.

In more serious circumstances, this could be triggered by the drive belt not being properly aligned, in which case it may be necessary to replace it.

Broken belt of a vacuum cleaner

A damaged belt in a vacuum cannot be repaired, therefore if you discover that your belt is broken, you can easily have it changed with the assistance of a professional. It is the belt that is responsible for moving the roller brushes, which is located at the base of the vacuum. The cost of replacing the belt ranges between Rs 200 and Rs 500, and the process of putting it on is simple, requiring only by use of a screwdriver to secure the roller brush in its proper position.

 If you are unable to demonstrate the ability to complete the task, we recommend that you seek professional assistance. Also, avoid using a vacuum cleaner until the belt has been replaced, as the motor may fail if this is not done.

If it fails to suck

This is most likely the most common problem associated with vacuum cleaners. When your vacuum is unable to produce adequate suction, the answer is usually straightforward.

Remove everything from the bag and chamber. This is the initial stage, which you have most likely already completed.

It’s possible that your height setting is incorrect. If the height setting on your vacuum is set very high for the floor you’re trying to clean, it won’t perform a very good job of cleaning. When working with tile or wood, start with the bare floor level and adjust upwards as needed. When it comes to a hardwood floor, a thick carpet setting will not help you much.

Check your filters.

 If the exhaust or air filter in your vacuum cleaner is clogged, it will most likely not be able to suction very well. Air and/or exhaust filters should be cleaned or replaced regularly. Viola!

Check your hose.

If the hose of your vacuum cleaner becomes clogged, it will be unable to perform its primary function. If you suspect that something is impeding your vacuum hose, unplug it from the machine immediately. After that, smooth it up and shine a light by one end & see if any light comes from the other end of the tube. If that doesn’t work, use a blunt tool to try to extract whatever is obstructing the airflow; just be careful not to damage or tear the hose in the process.

Check the brush roll.

Is it spinning or not? A possible explanation for this might be because it is overburdened with hair. A situation like this will arise for anyone who has pets, children, or partners with long hair at some point.

If your brushing roll is tidy, but it is still not spinning, you most likely have a problem with the belt. Don’t get too worked up over it. It occurs regularly. It’s probably the most prevalent issue we see with vacuums. Belts aren’t prohibitively expensive, and they’re not particularly difficult to replace.

Related Topics

Reply